FOR SALE SUMMARY PAGE
*COTTON PICKERS FOR SALE  * MODULE TRUCKS FOR SALE  *BOLL BUGGY(S) FOR SALE  *JOHN DEERE 8130 TRACTOR FOR SALE
* JOHN DEERE 6420 BOOM MOWER FOR SALE  * USED COMBINES FOR SALE

  “Farmers Who Know Cottonpickers.com Know Where to Buy Their Equipment”
For Australia Cotton Picker Sales - We are convenient to Ocean Terminal.

CALL US TODAY!
(706) 836-2106   (602) 369-6064

DOUBLE CLICK HERE OR ON PICTURE TO SEE MORE DETAILED PHOTOS OF THIS COTTON PICKER

DOUBLE CLICK HERE OR ON PICTURE TO SEE MORE DETAILED PHOTOS OF THIS COTTON PICKER

• Took out all spindles in front drums and replaced with new spindle nut assembles.
• Took bad spindles out of back drums and replaced them with good used spindle assemblies.
• Replaced clear and green water lines from machine to units.
• Replaced clear moisture column top housings, water lines in unit cabinets and lines going to moisture column tips.
• Took out and repaired bars with stripped gears on spindle shafts.
• Took old pads off moisture columns, checked alignment and put on new pads.
• Replaced plastic liners on height sensor shoes.
• Replaced all gaskets on unit inspection doors.
• Took all doffers out and put new doffer stalks in front drum and put good used ones in rear.
• Put new decals on all units.
• Replaced all long and short inside basket door wooden chain protectors.
• Replaced all basket outside bottom chain protectors.
• Took rear basket extension cylinder off and put a kit in it.
• Replaced solution pump belt
• Replaced all outer basket door chain protectors.
• Replaced one long drive cover to units.
• Replaced all moisture column bottom bushings.
• Replaced middle section of #2 section air duct.
• Took one steering cylinder off and put a repair kit in it.
• Replaced one unit cross shaft cover.
• Replaced two basket extension front screens.
• Replaced electric flush valve.
• Replaced one water manifold.
• Changed engine oil and filter, both engine fuel filters, inner and outer engine air filters, inner and outer cab air condition filters.
• Replaced cab windshield wiper blade,
• Took basket door cylinder off and replaced with new cylinder.
• Changed hydraulic oil and all filters.
• Took both unit lift cylinders off and put repair kits in them.
• Replaced fire extinguisher port grommets in shields as needed.
• Changed oil in both final drives.
• Changed oil in transmission.
• Drained radiator and put in new antifreeze.
• Shimmed bars and set moisture columns and doffers.
• Set pressure doors.
• Checked water system.
• Greased units and rear of machine.

DOUBLE CLICK HERE OR ON PICTURE TO SEE MORE DETAILED PHOTOS OF THIS COTTON PICKER

• Removed all spindles and replaced with new spindle nut assemblies.
• Removed bad spindles out of back drums and and replaced them with hand graded like-new nut assemblies.
• Replaced clear and green water lines from machine to units.
• Replaced clear moisture column top housing.
  
• Replaced water lines in unit cabinets and lines going to moisture column tips.
• Removed and repaired bars with stripped gears on spindle shaft
• Removed old pads off moisture columns, checked alignment and put on new pads.
• Replaced plastic liners on height sensor shoes.
• Replaced all gaskets on unit inspection doors.
• Removed all doffers and put new doffer stalks in front drum and replaced with high quality used ones in rear.
  
• Put on new decals on all units.
• Replaced one basket lid extension side screen.
• Replaced one basket extension rear screen and two back lower front screens.
• Replaced solution pump belt.
• Replaced one long unit drive shaft cover, two pressure door plastic extension and one fuse panel in hydraulic compartment.
• Replaced one basket light.
• Replaced all moisture column bottom bushings.
• Replaced pipe from turbocharger to muffler.
• Replaced all brushes in basket door, water transducer, electric flush valve, one compact bearing and both rear channels for warning lights.
• Changed engine oil and filter, both engine fuel filters, inner and outer engine air filters, inner and outer cab air condition filters.
• Changed cab windshield wiper blade.
• Removed basket door cylinder and replaced with new cylinder.
• Drained all hydraulic oils and replaced with new, including all filters (internal reservoir filters also).
• Removed both unit lift cylinders and put repair kits in them.
• Replaced fire extinguisher port grommets in shields as needed.
• Changed oil in both final drives.
• Changed oil in transmission.
• Drained engine coolant and replaced with new extended life coolant.
• Shimmed bars and set moisture columns and doffers, all bars shimmed within 3,000 to 5,000 tolerance.
  
• Set pressure doors.
• Checked water system.
• Greased units and rear of machine.
• All sight glass, water and fuel replaced.

• Took out all spindles in front drums and replaced with new spindle nut assembles.
• Took bad spindles out of back drum and replaced them with good used spindle assemblies.
• Took bars out of front drums and re-sleeved bars.
• Took off old bar bottoms and put new ones on.
• Replaced bar stools.
• Replaced cam tracks and cam bushings.
• Aligned cam tracks and doffer with alignment tolls.
• Replaced o-rings in bar journals.
• Checked all roll pins in bar shafts and replaced as needed
• Replaced clear and green water lines from machine to units.
• Replaced clear moisture column top housings.
• Replaced water lines in unit cabinets and lines going to moisture column tips.
• Took out and repaired bars with stripped gears on spindle shafts.
• Took old pads off moisture columns, checked alignment and put on new pads.
• Replaced plastic liners on height sensor shoes.
• Replaced all gaskets on unit inspection doors.
• Took all doffers out and put new doffer stalks in front drum and good used ones in rear.
• Took out old crop fan and put in new “California” fan.
• Put new decals on all units.
• Replaced bushing in row-trak guides.
• Changed engine oil and filter.
• Changed both engine fuel filters.
• Changed inner and outer engine air filters.
• Changed inner and outer cab air condition filters.
• Replaced cab windshield wiper blade.
• Took basket door cylinder off and replaced with new cylinder.
• Changed hydraulic oil and all filters.
• Took both unit lift cylinders off and put repair kits in them.
• Replaced fire extinguisher port grommets in shields as needed.
• Changed oil in both final drives.
• Changed oil in transmission.
• Drained radiator and put in new antifreeze.
• Replaced rear engine oil seal and put on new oil pan gasket.
• Shimmed bars and set moisture columns and doffers.
• Set pressure doors.
• Checked water system
• Greased units and rear of machine.

• Took out all spindles in front drums and rear drums, replaced with new spindle nut assemblies.
• Replaced clear and green water lines from machine to units.
• Replaced clear moisture column top housings.
• Replaced water lines in unit cabinets and lines going to moisture column tips.
• Took out and repaired bars with stripped gears on spindle shafts.
• Took old pads off moisture columns.
• Checked alignment and put on new pads.
• Replaced plastic liners on height sensor shoes.
• Replaced all gaskets on unit inspection doors.
• Took all doffers out and put new doffer stalks in front drum and put good used ones in rear.
• Took out old crop fan and put in new “California” fan.
• Put new decals on all units.
• Replaced all basket inside wooden chain protectors.
• Replaced all long and short inside basket door wooden chain protectors.
• Replaced one basket lid extension side screen,
• Replaced hydraulic pump belt.
• Replaced all basket outside bottom chain protectors.
• Replaced bushing in row track guides.
• Replaced all basket door outer chain protectors, one basket extension rear screen, inside basket light, one final drive seal, solution pump belt. Rotary screen drive belt, rotary screen brush, and rotary screen door.
• Took link out of basket floor chain and adjusted.
• Replaced one pressure door plastic extension.
• Replaced all moisture column bottom bushings.
• Replaced one long drive shaft cover to units.
• Replaced all unit cross shaft covers.
• Replaced radio antenna.
• Replaced electric flush valve, 4’ of 3” air duct going to units.
• Replaced one outside mirror.
• Replaced one bearing on shaft pulling rotary screen belt.
• Changed engine oil and filter, both engine fuel filters, inner and outer engine air filters.
• Replaced cab windshield wiper blade.
• Changed hydraulic oil and filters.
• Took both unit lift cylinders off and put repair kits in them.
• Replaced fire extinguisher post grommets in shields as needed.
• Changed oil in both final drives.
• Changed oil in transmission.
• Drained radiator and put in new antifreeze.
• Replaced rear end oil seal and put on new oil pan gasket.
• Shimmed bars and set moisture columns and doffers.
• Set pressure doors.
• Checked water system.
• Greased units and rear of machine.
• Replaced all cross shaft covers on units.

• Took out all spindles in front drums and replaced with new spindle nut assemblies.
• Took bad spindles out of back drums and replaced them with good used spindle assemblies.
• Replaced clear and green water lines from machine to units.
• Replaced clear moisture column top housings.
• Replaced water lines in unit cabinets and lines going to moisture column tips.
• Took out and repaired bars with stripped gears on spindle shafts.
• Took old pads off moisture columns, checked alignment and put on new pads.
• Replaced plastic liners on height sensor shoes.
• Replaced all gaskets on unit inspection doors.
• Took all doffers out and put new doffer stalks in front drum and good used ones in rear.
• Took out old crop fan and put in new “California” fan.
• Put new decals on all units.
• Replaced all basket inside wooden chain protectors,
• Replaced all long and short inside basket door wooden chain protectors.
• Replaced two basket lid extension side screens.
• Replaced hydraulic pump belt.
• Replaced all basket outside bottom chain protectors, bushings in row-trak guides.
• Replaced engine oil and filter, both engine fuel filters, inner and outer engine air filters, inner and outer cab air conditioner filters.
• Replaced cab windshield wiper blade.
• Took basket door cylinder off and replaced with new cylinder.
• Changed hydraulic oil and all filters.
• Took both unit lift cylinders off and put repair kits in them.
• Replaced fire extinguisher port grommets in shields as needed.
• Changed oil in both final drives.
• Changed oil in transmission.
• Drained radiator and put in new antifreeze.
• Replaced rear engine oil seal and put on new oil pan gasket.
• Shimmed bars and set moisture columns and doffers.
• Set pressure doors.
• Replaced actuator to control water pressure.
• Replaced four cross shaft covers on units.
• Replaced sump screen in transmission.
• Checked water system.
• Greased units and rear of machine.

• Took out all spindles in front drums and replaced with new spindle nut assemblies.
• Took bad spindles out of back drums and replaced them with good used spindle assemblies.
• Took bars out of ftont drums and re-sleeved bars.
• Took off old bar bottoms and put new ones on.
• Replaced bar stools.
• Replaced cam tracks and cam bushings.
• Aligned cam tracks and doffers with alignemtn tools.
• Replaced o-rings in bar journal.
• Checked all roll pins in bar shafts and replaced as needed.
• Replaced clear moisture column top housings.
• Replaced water lines in unit cabinets and lines going to moisture column tips.
• Took out and repaired bars with stripped gears on spindle shafts.
• Took old pads off moisture columns, checked alignment and put on new pads.
• Replaced plastic liners on height sensor shoes.
• Replaced all gaskets on unit inspection doors.
• Took all doffers out and put new doffer stalks in front drum and good used ones in rear.
• Took out old crop fan and put in new “California” fan.
• Put new decals on all units.
• Replaced one front hazard bracket and light.
• Replaced one right side basket extension screen, both row-trac guides, one stalk lift front bracket, one complete plastic stalk lift.
• Replaced one front basket extension screen.
• Replaced bushing in tow-trak guides.
• Changed engine oil and filter, both engine fuel filters,, inner and outer engine air filters, inner and outer cab air condition filters.
• Replaced cab windshield wiper blade.
• Changed hydraulic oil and all filters.
• Replaced fire extinguisher port grommets in shields as needed.
• Changed oil in both final drives.
• Changed oil in transmission.
• Drained radiator and put in new antifreeze.
• Replaced rear engine oil seal and put on new oil pan gasket.
• Shimmed bars and set moisture columns and doffers.
• Set pressure doors.
• Checked water system.
• Greased units and rear of machine.
• Replaced four cross shaft covers on units.
• Replaced sump screen in transmission.

SOLD

CALL 706-836-2106 TODAY TO SEE WHAT MODULE TRUCKS WE CURRENTLY HAVE FOR SALE

CALL 706-836-2106 TODAY TO SEE WHAT MODULE TRUCKS WE CURRENTLY HAVE FOR SALE

Actual Miles - 135,309 

2006 Crust Buster Boll Buggy For Sale SOLD
Lift and Shift Model
Single Motor Chain Unload   
sheltered

SOLD

SOLD

* C12 Caterpillar
* 380 Hp
* Completely Serviced (All Filters & Oil)

SUSPENSION:
* Air Ride Cab & Suspension

 TRUCK BED:
 *Triple J Bed
* Electric Over Hydraulic

MISC:
* Tires Original 85%
* New Windshield Wipers

2009 John Deere 6700 Sprayer SOLD

SOLD

* Completely Serviced (Engine, Oil & Hydraulic Filters) & Greased

* New Air Filters (Engine & Cab)

2005 John Deere 9650 STS Combine SOLD

Call (706) 836-2106 for updated inventory of Combines

2004 JD 9986 Cotton Picker Stock # 74  w/mud hogs (late serial number, 9996 style) and auto-trac: SOLD

New R1 Firestone 20.8 42s
New High Velocity Crop Fan
New Crop Fan Belt and New Belt Idler Engine Tension-er
All New Complete Water Lines, Flush and Pressure
All New Moisture Columns, Top Housing and O-Rings, Alignment Bushings and Alignment
All New Spindle Nut Assembly, Pro XL
All New Doffer Pads and Ground
All New Moisture Pads
All New Plastic Height Sensor Shoes
New Gasket Header Inspection Doors
All Spindle Bars Shimmed Within 5,000 Tolerance
Grease Tank Cleaned and All New Spindle Grease Flushed
Water Tank Cleaned and Flushed
New Pressure Transducer Installed
All Tips and Screens Cleaned and Serviced
Replaced All Top Bearings on Unit Drum Slip Clutches
Replaced Front Pressure Doors w/ New Style Doors (9996)
Replaced 4 Stalk Guide Channel Brackets
Installed 2 New Lift Cylinders for Header Frame
Row Track Re-Calibrated and Tested
Brakes Checked and Replaced w/New Brake Shoes, Drums and Reservoir
Engine Oil and Filters Changed
Engine Air Filters (Outer and Inner) Changed
New Fuel Filters (Primary and Secondary)
Cab AC Filters (Outer and Inner) Changed
All Hydraulic Oil Changed, Filters, Inside Reservoir and Hydrostatic
All Gear Boxes Oil Changed and Replaced w/John Deere High Velocity
Radiator Cleaned, Drained and Flushed, Replaced w/New Extended Life Coolant
New Final Drive Fluid and Transmission Replaced and Checked

 
SOLD "Call (706) 836-2106 today to see what other cotton pickers we have in stock."
Let us know what you are looking for. We are updating inventory daily.

 

• Took out all spindles in front drum and replaced with new spindle nut assemblies.
• Took bad spindles out of back drums and replaced them with good used spindle assemblies.
• Replaced clear and green water lines from machine to units.
• Replaced clear moisture column top housings.
• Replaced water lines in unit cabinets and lines going to moisture column tips.
• Took out and repaired bars with stripped gears on spindle shafts.
• Took all pads off moisture columns, checked alignment and put on new pads.
• Replaced plastic liners on height sensor shoes.
• Replaced all gaskets on unit inspection doors.
• Took all doffers out and put new doffer stalks in front drum and good used ones in rear.
• Took out old crop fan and put in new “California” fan.
• Put new decals on all units.
• Replaced all long and short inside basket door wooden chain protectors.
• Replaced one basket lid extension side screen.
• Replaced hydraulic pump belts.
• Replaced bushing in row-trak guides.
• Replaced two shaft covers on units, two compactor bearings in basket, two rear basket extension screens, one basket door safety tube, one hazard light rear bracket, solution pump belt, rotary screen brush and drive belt.
• Replaced bad cotton doors with good used ones, rotary screen main drive belt from engine.
• Took link out of the floor chain and adjusted.
• Changed engine oil and filter, both engine fuel filter, inner and outer engine air filters, inner and outer cab air condition filters.
• Replaced cab windshield wiper blade.
• Changed hydraulic oil and all filters.
• Took unit lift cylinders off and put repair kits in them.
• Replaced fire extinguisher port grommets in shields as needed.
• Changed oil in both final drives.
• Changed oil in transmission.
• Drained radiator and put in new antifreeze.
• Shimmed bars and set moisture columns and doffers.
• Set pressure doors.
• Checked water system.
• Greased units and rear of machine.

• Took out all spindles in front drums and replaced with new nut assemblies.
• Took bad spindles out of back drums and replaced them with good used assemblies.
• Replaced clear and green water lines from machine to units.
• Replaced clear moisture column top housings.
• Replaced water lines in unit cabinets and lines going to moisture column tips.
• Took out and repaired bars with stripped gears on spindle shafts.
• Took old pads off moisture columns, checked alignment and put on new pads.
• Replaced plastic liners on height sensor shoes.
• Replaced all gaskets on unit inspection doors.
• Took all doffers out and put new doffer stalks in front drum and good used ones in rear drum.
• Took out old crop fan and put in new “California” fan.
• Put on new decals on all units.
• Replaced all basket inside wooden chain protectors.
• Replaced all long and short inside basket door wooden chain protectors.
• Replaced one basket lid extension side screen.
• Replaced hydraulic pump belt.
• Replaced all basket outside bottom chain protectors.
• Replaced all moisture column bottom bushings.
• Replaced cab windshield wiper blade.
• Replaced long cover on drive shaft going to units, one rotary screen door latch, rotary screen brush, rotary screen belt, one basket door safety tube.
• Replaced all basket door outer chain protectors.
• Replaced electric flush valve.
• Replaced front and rear grid bars and nuts as needed.
• Replaced engine air filter housing.
• Changed engine oil and filter, both engine fuel filters, inner and outer engine air filters, inner and outer cab air condition filters.
• Took basket door cylinder off and replaced with new cylinder.
• Changed hydraulic oil and all filters.
• Took one unit lift cylinder off and put repair kits in.
• Replaced fire extinguisher port grommets in shields as needed.
• Changed oil in both final drives.
• Changed oil in transmission.
• Drained radiator and put in new antifreeze.
• Shimmed bars and set moisture columns and doffers.
• Set pressure doors.
• Checked water system.
• Greased units and rear of machine.